Main Menu

Winter Pool Cover Care: How to Keep Your Cover (and Your Pool) Happy Until Spring

This entry was posted on by mpsblog.

Your pool is closed, the cover is on, and you've officially entered the "out of sight, out of mind" season. Tempting, right? Unfortunately, your winter cover didn't get the memo that it gets to relax too. Between rain, snow, leaves and the occasional curious squirrel, it's working hard all winter long.

The good news: keeping a pool cover in good shape takes about as much effort as checking the weather. A quick look every week or so (and after every big storm) can save you a torn cover, a swampy mess and a very unpleasant spring opening. Here's how to do it, based on guidance from pool cover manufacturers.

Quick heads-up: Every cover is a little different. If anything here disagrees with your cover's manual, the manual wins.

Step 1: Know what kind of cover you have

How you care for your cover depends on what it's made of:

  • Solid covers block water, sunlight and debris. Great for keeping the pool clean, but rain and melted snow sit on top. That water has to go somewhere, and "somewhere" is your job.
  • Mesh safety covers let rain and melting snow drain through into the pool while catching leaves and debris. Less bailing, but the water level in the pool needs watching.
  • Above-ground winter covers are usually solid covers held on with a cable and winch, often with an air pillow floating underneath.

Step 2: Get rid of standing water (solid covers)

A puddle on a solid cover is more than an eyesore. Water is heavy, and a big pond on top can stretch the cover, pull at anchors or the top rail, and on above-ground pools even drag the cover right into the pool. Not the kind of winter swim anyone signed up for.

  1. Use a cover pump. A small submersible pool cover pump sits on the cover and pumps the water off. Many have an automatic switch, so you can leave it out during rainy stretches.
  2. Pump often, not just when it's a lake. It's much easier to move a few inches of water than a foot of it.
  3. Point the discharge hose away from the pool so you're not just giving that water a round trip.
  4. Don't pump if the pool water is coming up through a hole. If the water on top is suddenly clear and chlorinated, the cover may have a tear, and you'd be draining your pool. Patch it first.

Step 3: Keep the pool water at the right level

This one is easy to forget, and it matters a lot. The water under the cover helps hold up the weight of snow and ice. If it drops too low, the cover takes all that load by itself.

  • Mesh covers: manufacturers commonly recommend keeping the water roughly 15 to 18 inches below the top of the pool all winter. Too low stresses the cover, and too high can freeze into the cover and skimmer area.
  • Solid covers: follow your cover's specific water level, and keep the water on top pumped off.
  • Check after big rains and snow melts. If the water is too high, a cover pump can lower it, but stop at the recommended level. If it's too low, top it off.

Step 4: Clear leaves and debris the gentle way

Leaves on a cover turn into a soggy, heavy, tea-colored mush that stains the cover and loves to sneak into the pool on opening day.

  • Scoop them off regularly with a deep-bag leaf rake or a simple economy leaf rake. A professional leaf rake holds a lot more before you have to empty it.
  • Keep it soft. Skip garden rakes, shovels and anything with sharp edges or stiff metal tines. They poke holes faster than you can say "how much is a new cover?"
  • Trim back overhanging branches when you can. Fewer leaves, and fewer branches dropping onto the cover in a windstorm.

Step 5: Snow and ice: mostly, leave them alone

Yes, really. Your shovel is not invited.

  • Mesh safety covers are built to handle snow, and manufacturers say there's no need to clear it off. Let it melt and drain through, then check the water level.
  • Don't chip at ice. If ice forms on the cover, wait for it to melt. Hacking at it is a great way to make a hole.
  • Solid covers with heavy snow: if you're worried, gently brush light snow off with a soft broom, never a shovel, and pump off the melt water as soon as it thaws.

Step 6: Check what's holding it all in place

A cover is only as good as whatever keeps it on the pool. Every few weeks, take a walk around:

  • Water tubes (solid in-ground covers): make sure they're lying flat and overlapping the cover edge. Fill them only about halfway, since water expands when it freezes and an overfilled tube can split. Swap out any that are leaking for a new water tube.
  • Safety cover straps and springs: look for loose straps, stretched springs or anchors that popped up. A worn safety cover strap buckle is an easy fix now and a much bigger deal later.
  • Above-ground covers: make sure the cable is snug and the cover winch is doing its job. Cover clips help keep wind from sneaking under the edge, and winter cover wrap adds an extra layer of hold around the top rail.
  • Air pillow (above-ground pools): it should be roughly centered and inflated only partway, around half to two-thirds full, so it can squish as ice pushes on it. If yours has given up, grab a new pool air pillow.

Step 7: Patch small problems before they become big ones

A tiny tear in November is a giant tear by March, especially with wind, snow and water weight pulling on it.

  • Mesh covers: a mesh cover repair patch handles small holes. Follow the patch instructions and apply it on a dry day.
  • Solid covers: use a vinyl patch kit made for pool covers, on a clean, dry spot.
  • Big rips or a cover that's falling apart: time to start shopping for a replacement before spring, not on opening day.

Step 8: Peek at the water now and then

Pull back a corner every few weeks and take a look. A little cloudiness is normal. Green is not. Keeping the water balanced and adding a winterizing product like winter aid (always follow the label) helps keep algae from throwing a party under there while you're not looking.

Bonus: When spring finally shows up

When it's time to open, pump off the water and scoop off debris before you take the cover off, so all that gunk doesn't slide straight into the pool. Then clean the cover with mild soap and fresh water, let it dry completely, and store it folded in a cool, dry place off the ground. A cover put away wet comes back smelling like a gym bag, and nobody wants that.

The short version

  • Pump standing water off solid covers, often.
  • Keep the pool water at the level your cover maker recommends.
  • Scoop leaves with a soft leaf rake, never a sharp tool.
  • Leave snow and ice alone on mesh covers.
  • Check tubes, straps, springs, cables and air pillows every few weeks.
  • Patch small holes before they grow.

Do that, and your cover will make it to spring in one piece, and so will your pool. Need a cover pump, leaf rake, water tubes or other winter gear? You'll find it all at Major Pool Supplies.


← Older Post